CCTV Design Tool Guide: Lens and Coverage Calculators, Drawing and Simulation Software, and What to Ask Your Designer

CCTV Design Tool Guide: Lens and Coverage Calculators, Drawing and Simulation Software, and What to Ask Your Designer

A CCTV design tool helps the designer place cameras, choose lenses and calculate field of view, storage and bandwidth before anything is ordered. The tools fall into three groups: lens and coverage calculators, storage and network calculators, and 2D/3D drawing and simulation software. Software alone does not make a good design, though. What matters is what the designer hands over: a layout plan, a camera schedule and calculations you can check. AZEIDK prepares these deliverables following the approach of its engineering design and calculations service, then delivers the system under its security and surveillance solutions.

Key Points

  • A lens calculator links focal length to distance, scene width and the pixel density you need.
  • A storage calculator sizes the hard disks from camera count, resolution, bitrate and retention days.
  • Design software places cameras on the building plan and shows field of view and DORI zones.
  • Some tools are free online; others are paid programs with trial versions from their developers.
  • Ask the designer for written deliverables, not screenshots from a program.
In this article
  1. What Does a CCTV Design Tool Calculate?
  2. Types of CCTV Design Tools
  3. Examples from Developers’ Own Pages
  4. CCTV Calculator: Lens First, Then Storage
  5. Drawing and Simulation Software: What It Adds and Where It Stops
  6. What to Ask Your CCTV Designer For
  7. How AZEIDK Turns Design Tools into a Buildable Layout
  8. Frequently Asked Questions
  9. Conclusion

What Does a CCTV Design Tool Calculate?

Any CCTV design tool answers a short list of questions: where the camera goes, at what height, with which lens, and what it will show at a given distance. Movement only, or a face you can recognise? Then: how much storage, bandwidth and PoE power the system needs.

Most tools ask for the same inputs: sensor size and resolution, focal length, mounting height, distance to the target and the required scene width. The key output is pixel density on the target, expressed in pixels per metre (PPM) or pixels per foot (PPF). Higher density means more usable detail.

Many designers work with DORI: Detection, Observation, Recognition and Identification. JVSG states on its product page that the DORI zones its software displays are based on IEC/EN 62676-4. Defining the target for each camera before picking a lens is what separates a design from a guess.

Types of CCTV Design Tools

Tool typeWhat it doesWhen to use it
Lens and field-of-view calculatorCalculates focal length, scene width and pixel density for one cameraChoosing the lens for a specific spot: gate, cashier, corridor
Storage and bandwidth calculatorEstimates storage and network load from camera count, resolution and retentionSizing the NVR, hard disks and switches
2D/3D design and simulation softwarePlaces cameras on the plan and shows coverage and blind spotsMulti-storey buildings, outdoor sites and warehouses
Drawing software (CAD, Visio)Produces the layout plan, riser and network diagramDrawings for the consultant and shop drawings
Manufacturer product selectorsHelp pick the model and accessories (brackets, junction boxes)After the design is fixed, when preparing the BOQ

Examples from Developers’ Own Pages

The examples below are described as their developers describe them, in no particular order. Naming them is not a ranking and does not mean they are the required tools on every project.

  • JVSG IP Video System Design Tool: Windows software that JVSG describes as 3D video surveillance design software. Its page lists lens and sensor calculations to reach a target pixel density, DORI zone display, bandwidth and storage estimates, AutoCAD DWG import in the higher editions, and export to PDF and DWG/DXF. It is paid software with a trial version.
  • JVSG Online and CCTV Lens Calculator: JVSG states that its browser-based design tool is free while in beta and that its online lens calculator is free.
  • Dahua tools: Dahua’s official website has a tools section with categories including “Select Products or Calculation” and “Design Projects and Select Accessories”, a link to its project design tool (DSS Design Tool), and product and accessory selectors.

If the project uses Hikvision or Dahua cameras, the most accurate source for lens and field-of-view values is the official datasheet of the exact model, because generic calculators assume standard values that can differ slightly from the real camera.

CCTV Calculator: Lens First, Then Storage

Start with one question: what must this camera show? A camera at an entrance meant to identify faces or plates needs far higher pixel density than one watching general movement in a yard. Once the target is set, the lens calculator gives you the right focal length, or tells you the chosen resolution is not enough at that distance.

Storage comes next: camera count, resolution, compression (H.264 or H.265), frame rate, continuous or motion recording, and retention days. The full method is in our article on CCTV storage and bandwidth calculation, and switch power budgets are covered in PoE switches for CCTV.

Drawing and Simulation Software: What It Adds and Where It Stops

3D simulation is useful because the owner sees what each camera will see before installation, and blind spots behind columns and racks become obvious. Drawing software such as AutoCAD is what the formal layout plan is produced in, and some designers use Microsoft Visio with stencils for riser and network diagrams.

The limits are clear:

  • Software does not know real night lighting, sun glare on glass, or trees and signs added later.
  • It assumes standard lens and sensor values; the actual model may differ.
  • It does not decide cable routes, network room locations or power points on its own.

A site survey therefore stays part of the design, especially outdoors and in high-bay warehouses. Practical placement rules are in CCTV camera placement and coverage.

What to Ask Your CCTV Designer For

Whether the designer uses paid software or a free calculator, ask for deliverables you can check and price against:

  • A layout plan per floor with a number, direction and field of view for each camera.
  • A camera schedule: type (dome, bullet, PTZ), resolution, lens, mounting height and target (detect, recognise or identify).
  • Storage and bandwidth calculation with retention days and the number and size of hard disks.
  • Network or riser diagram: switches, PoE budget, cable routes and network rooms.
  • Control room fit-out: monitors, workstations and management software.
  • A BOQ and technical specification so quotations can be compared on the same basis.

The same list helps when comparing contractors, as covered in what to ask a CCTV company before signing.

How AZEIDK Turns Design Tools into a Buildable Layout

AZEIDK’s scope covers the design, supply, installation and maintenance of CCTV and access control systems, the same scope stated on the company’s ISO 9001, ISO 14001 and ISO 45001 certificates. In practice the work starts from the architectural drawings or a site survey, then the target for each camera, then the calculations (lens, storage, network), then the layout plan, camera schedule and BOQ, and finally a review with the owner or consultant before procurement.

Once approved, the system is delivered under security and surveillance systems and handed over with recording settings and user permissions. If the project needs a maintenance contract, CCTV and low-current maintenance sits in a separate contract from fire and alarm system maintenance.

Frequently Asked Questions

Is there a free CCTV design tool?

Yes, some tools are free online, such as JVSG’s lens calculator and JVSG Online, which the company says is free while in beta. Full design programs are usually paid, with trial versions on the developers’ sites.

What is a CCTV calculator?

A tool that works out the right lens, scene width and pixel density at a given distance, or the storage needed for a retention period. Each calculator answers one question.

Can CCTV simulation software replace a site survey?

No. Software does not know night lighting, real obstructions or cable routes, so a survey is still needed for outdoor sites and warehouses.

What is the difference between design software and CCTV viewing software?

Design software is used before procurement to set locations, lenses and storage. Programs such as iVMS-4200 and SmartPSS run the system after installation; see our guide to CCTV software for PC.

What does DORI mean in CCTV design?

Four levels of detail: Detection, Observation, Recognition and Identification. The designer sets the level for each camera, then picks the resolution and lens that achieve it at the real distance.

What should a CCTV design package include?

A layout plan per floor, a camera schedule with lenses and targets, storage and network calculations, a network diagram, and a BOQ with technical specifications.

Conclusion

A CCTV design tool speeds up the calculations and makes coverage visible, but it is a tool in the designer’s hands, not a replacement for one. Set the target for each camera first, use lens and storage calculators to check, and ask for written deliverables you can review before you buy.

Planning CCTV for a building, warehouse or compound? Send the drawings and the areas you need covered, and the AZEIDK team will prepare the design, camera schedule and storage calculations. Contact the AZEIDK team

References: IP Video System Design Tool, JVSG (https://www.jvsg.com/ip-video-system-design-tool/); JVSG home page and tool list (https://www.jvsg.com/); Dahua Technology official website, tools section (https://www.dahuasecurity.com/); Engineering design and calculations service, AZEIDK (https://azeidkgroup.com/en/sa/services/engineering-design-calculations/).
Share this article
This site is registered on wpml.org as a development site. Switch to a production site key to remove this banner.