Hikvision camera activation is a required first step: a new camera or recorder leaves the factory in an Inactive state with no password, and it will not work until you create an admin password. The easiest way is Hikvision’s free SADP tool. It finds devices on the network, you select the inactive device, type a new password and click Activate, then change the IP address to match your network. This guide walks through the steps and explains why a camera may not show up on the recorder, as part of AZEIDK security and surveillance systems.
Key takeaways
- An inactive device will not accept a login and cannot be added to a recorder until an admin password is created.
- SADP shows a Status column for every device: Active or Inactive.
- Hikvision network cameras share one factory default address, so connecting several new cameras together causes address conflicts.
- After activation, give each camera a unique IP address inside your network range.
- Keep the password safe. Recovery goes through official support, not unofficial tools.
In this article
- What does Inactive mean on a Hikvision camera?
- What is SADP?
- What to prepare before activation
- Hikvision camera activation with SADP, step by step
- First password requirements
- Changing the IP address in SADP
- Why is my Hikvision camera not detected by the recorder?
- Other ways to activate a Hikvision camera
- Forgot the Hikvision camera password after activation
- Frequently asked questions
- Conclusion
What does Inactive mean on a Hikvision camera?
For several years Hikvision has shipped its devices without a default password, for network security reasons. A new device stays Inactive until the user creates a strong admin password at first use. While it is inactive, you cannot log in to the camera with an old default password, and you cannot add it to a recorder in the normal way.
So when someone says “the camera does not show up”, the first question is whether it has been activated at all. The answer is in the Status column in SADP.
What is SADP?
SADP stands for Search Active Devices Protocol. It is a free Hikvision tool for Windows that searches for Hikvision devices on the same local network and lists each device’s type, status, IP address, port, firmware version and serial number. From it you can activate a device, change its network settings and start password recovery. Download it only from Hikvision’s official website.
What to prepare before activation
- A Windows PC with the latest SADP version from Hikvision’s website.
- A sound network cable, and a PoE switch or a power adapter that suits the camera’s datasheet.
- An IP plan: the address range, the router address, and the addresses reserved for cameras and the recorder.
- A list of camera serial numbers and mounting locations, so you can identify each camera in SADP before changing its address.
This saves a lot of time on projects with dozens of cameras, because every new camera first appears on the same address and they are hard to tell apart without the serial number.
Hikvision camera activation with SADP, step by step
- Connect: put the camera and the PC on the same switch or router, and make sure the camera is powered (PoE or a power adapter).
- Search: open SADP. It searches automatically. If the camera is not listed, click Refresh.
- Select: tick the device whose status is Inactive.
- Password: enter the new password in New Password and repeat it in Confirm Password.
- Activate: click Activate. The status changes to Active.
- Network settings: change the IP address as described in the next section.
When you activate several cameras, do them one at a time and change each camera’s address right after activating it, so addresses do not clash and cameras do not drop out of the list.
First password requirements
Hikvision devices ask for a strong password at activation. The company’s manuals recommend at least 8 characters combining more than one of these types: upper case letters, lower case letters, numbers and special characters. The interface shows a strength indicator before it accepts the password. The exact minimum differs slightly between models and firmware versions.
Practical tips:
- Do not use the company name, a mobile number or a sequence such as 12345678.
- Record the password in the system handover file and give it to the site’s system owner along with each device’s serial number.
- If the recorder will activate the cameras, use one password known to the system administrator, then change it later in line with the site’s policy.
Changing the IP address in SADP
Hikvision network cameras ship with a default address, and Hikvision’s network camera user manual gives it as 192.168.1.64. If your network uses another range, such as 192.168.0.x or 10.0.0.x, the camera will not open in a browser until you change its address.
| SADP field | What to enter |
|---|---|
| Enable DHCP | Tick it if you want the router to assign the address. A fixed address is better for cameras |
| IPv4 Address | An unused address inside your network range |
| IPv4 Subnet Mask | The same subnet mask the router uses |
| IPv4 Default Gateway | The router’s address |
| Administrator Password | The password you created at activation, to confirm the change |
Then click Modify. Give cameras addresses outside the router’s DHCP range, or reserve addresses for them in the router, so no other device takes a camera’s address after a power cut. If the recorder later shows an IP Conflicted message, this is usually why. Our CCTV installation guide for Saudi Arabia covers network planning in more detail.
Why is my Hikvision camera not detected by the recorder?
| Cause | How to confirm | Fix |
|---|---|---|
| Camera not activated | Status shows Inactive in SADP | Activate it in SADP or from the recorder |
| Address conflict | Several cameras on the same default address | Change each camera’s address |
| Different network range | Camera address is outside the recorder’s range | Change the address and gateway |
| Wrong password when adding | Channel appears with a username or password error | Enter the camera’s correct password |
| No power or no link | Camera does not appear in SADP at all | Check the cable, the PoE port and the power budget |
| Recorder capacity exceeded | Channel count or incoming bandwidth is above its limit | Check the recorder’s datasheet |
PoE power problems are common when cameras are added to an existing switch. See our article on PoE switches and the CCTV power budget. For the bandwidth a recorder receives, see our guide to NVR storage and bandwidth calculation.
Other ways to activate a Hikvision camera
From a web browser
If the PC is in the same address range as the camera, type the camera’s address into a browser and the activation page will ask you to create a password. Hikvision publishes these steps in its “Activate via Web Browser” documentation.
From an NVR
Many Hikvision NVRs can activate inactive cameras from the camera management menu, using the recorder’s own password or one you set. On NVRs with built-in PoE ports, a camera plugged into those ports is usually added automatically. The options in this menu vary by model, so check your recorder’s manual, for example for the Hikvision DS-7608NXI-K1B NVR available from AZEIDK.
Forgot the Hikvision camera password after activation
SADP includes a Forgot Password option. The SADP manual lists several methods depending on the device: exporting a request file or photographing a QR code and sending it to Hikvision’s official technical support, which returns a key; importing the GUID file saved at activation; or answering the security questions set at activation. Proof of ownership may be required, and the available method depends on the model and firmware. The official recovery routes for recorders are covered in Forgot CCTV password. Do not use unlock tools or modified firmware from unofficial sources: they can brick the device and open a security hole in your network.
Frequently asked questions
How do I activate a Hikvision camera for the first time?
Open SADP on a PC on the same network, select the camera showing Inactive, enter and confirm a new password, then click Activate.
What is the default password for Hikvision cameras?
Current devices have no default password. You create the admin password at first activation.
What is the default IP of a Hikvision camera?
Hikvision’s network camera manual gives 192.168.1.64. The reliable way is to read the current address in the IPv4 Address column in SADP.
Why can’t SADP find my camera?
Usually the camera has no power or its cable is disconnected, or it sits on a different network from the PC. Windows firewall can also block the search.
Can I activate a Hikvision camera from the recorder?
Yes on many Hikvision NVRs, from the camera management menu. Cameras plugged into the recorder’s own PoE ports are added automatically on most models.
The camera is active but still not detected. Why?
Check for address conflicts, the network range, the password entered when adding the camera and the recorder’s channel limit.
Conclusion
Hikvision camera activation comes down to three steps: a strong admin password, a unique IP address inside your network range, and adding the camera to the recorder with the right password. Most “camera not detected” cases come from one of these three steps, not from a faulty camera.
Need Hikvision cameras installed or an existing system configured? AZEIDK supplies cameras and recorders, installs them and sets up the network. Talk to the AZEIDK team
Related guides
- CCTV Recorder (NVR or DVR): How to Choose Channels, Resolution, Hard Drive and PoE Ports with Hikvision Models
- SFFECO Fire Hose Cabinet SF 300 and Automatic Hose Reel: When to Choose Them
- Hikvision in Saudi Arabia: CCTV and Access Control Systems
- ISO Certificates for Companies and Contractors in Saudi Arabia: ISO 9001, 14001 and 45001 in Tenders







