A CCTV maintenance SLA (service level agreement) is the part of the maintenance contract that turns “we will maintain your system” into numbers you can measure: how fast the technician responds to a call, when the fault is fixed, what share of the time recording must be available, and what happens when a target is missed. At AZEIDK this belongs in a separate low-current and CCTV maintenance contract, not in the fire and alarm systems contract. This guide explains how to write a clear SLA, which metrics are worth measuring, and what to ask your security and surveillance contractor before you sign.
Key takeaways
- A CCTV maintenance SLA sets response time, repair time and recording availability, and how each one is proven.
- Classifying faults as critical, major and minor is the basis for every number in the contract.
- The most important metric for surveillance is recording availability, not just a live picture on the monitor.
- The low-current and CCTV contract is separate from the fire and alarm maintenance contract, and each has its own SLA.
- Recording retention follows the Security Surveillance Cameras Law and the conditions document for your activity; the contract must protect that period.
In this article
- What is an SLA in a CCTV maintenance contract?
- Why is the low-current and CCTV contract separate from the fire contract?
- How should CCTV faults be classified in the SLA?
- Response time vs repair time: how to write them
- Recording availability: the metric many contracts miss
- Preventive visits and spare parts
- Monthly reports and proof of compliance
- What to ask the contractor before signing a CCTV maintenance SLA
- Frequently asked questions
- Conclusion
What is an SLA in a CCTV maintenance contract?
A standard CCTV maintenance contract lists the equipment and the number of preventive visits. The SLA is the schedule that ties the service to defined times and percentages and states how they are measured and recorded. Without it, every delay becomes a matter of opinion: the owner says a camera was down for a week, the contractor says he visited the next day.
The difference shows the first time the network video recorder (NVR) fails. With a clear SLA you know when the technician arrives, when a temporary replacement goes in, and when recording must be back. Without one, you only know there will be an “emergency visit”.
For the maintenance work itself (periodic checks, lens cleaning, hard disk health, firmware), see our article on CCTV system maintenance. This article covers the measurement and commitment terms only.
Why is the low-current and CCTV contract separate from the fire contract?
Fire and alarm systems have their own technical and regulatory framework: the Saudi Fire Protection Code, Civil Defense requirements and the maintenance records that inspections ask for. Cameras, access control, intercom and the network that serves them use different technicians, different spare parts and different performance indicators.
That is why AZEIDK works with two separate contracts: one for fire, safety and alarm systems, and another for low-current systems and CCTV. Each has its own SLA. This article deals with surveillance and low current only. The scope of these systems is on our low-current systems page.
How should CCTV faults be classified in the SLA?
A response time means nothing until fault severity is defined. The usual approach is three levels, written into the contract with examples from your own site:
| Severity | Examples | What the contract should set |
|---|---|---|
| Critical | NVR/DVR down, failed hard disk, a PoE switch feeding several cameras is off, main entrance or cash office cameras down | Shortest response time, mandatory temporary fix, written notice to management |
| Major | One non-critical camera down, poor night image, remote access failure | Longer response time, repair within a defined number of hours or days |
| Minor | Camera angle shifted, dirty lens, wrong date and time, user permission change | Handled at the next preventive visit or within an agreed period |
List the critical cameras by name or number in the schedule: entrances, cash points, warehouses, car parks. This prevents arguments later about whether a fault was critical.
Response time vs repair time: how to write them
Response time runs from the logged call until the technician starts work, remotely or on site. Repair time runs until the device or service is back to normal, or until a temporary replacement restores recording. Many contracts only state response time, so the technician arrives on time and the fault then stays open for days while a part is ordered.
Write both times for each severity level, and state whether hours run around the clock or within working hours only, and whether public holidays count. The figures depend on the city, site distance, system size and whether there is a resident technician, so there is no single value that suits every facility. What matters is that the numbers are written down and measurable.
Add a temporary-fix clause: if the permanent repair takes longer, the contractor restores recording with a spare recorder or disk until the permanent part arrives. This one clause closes the most serious gap in any surveillance system, which is time without recording.
Recording availability: the metric many contracts miss
A live picture in the control room does not mean the system is recording. Live view can work while the disk is full or failed, or the recording schedule has stopped. The SLA should therefore include recording availability: the share of the month in which the critical cameras were actually recording.
To make it measurable, the contract should state:
- The data source: recorder or video management software logs, video loss alarms and disk error events.
- The scope: critical cameras only, or all cameras with a different target.
- Exclusions: general power cuts, owner works on the network, third-party damage.
- Periodic proof: at each visit a clip from an earlier date is retrieved and exported to confirm it exists.
This metric is tied to the retention period. An Okaz report (8 January 2025) on the Executive Regulations of the Security Surveillance Cameras Law states that failing to keep recordings for the period set in the conditions document is a violation, and that footage linked to a reported incident must be kept intact until the investigation ends. Storage must be sized for that period; see CCTV storage and bandwidth calculation and our article on the Saudi surveillance cameras law.
Preventive visits and spare parts
Preventive visits are part of the SLA too, because skipping them raises the number of emergency faults. State how many visits per year and what each one covers, and ask for a signed report after every visit. Typical items are checking each camera image by day and night, disk health, time synchronisation, playback, lens cleaning, and power supplies and PoE switches.
For spare parts, state whether the contract is comprehensive or non-comprehensive, what the contractor replaces at its own cost and what is quoted separately. Ask for a “like-for-like or better” clause for models that are discontinued, and confirm the replacement works with the existing recorder and software. AZEIDK supplies Hikvision, Dahua and EZVIZ cameras and recorders in its CCTV cameras and recorders range.
Monthly reports and proof of compliance
An SLA without reports cannot be followed up. Ask for a short monthly report with the number of calls by severity, actual response and repair time for each call, calls that missed the target, recording availability, replaced parts and recommendations. Log every call through one time-stamped channel (email or a ticketing system) so both sides calculate times the same way.
The contract then states the consequence of a missed target: a deduction from the monthly invoice, a free extension of the contract term, or a right to terminate after a defined number of repeat failures. The amount is a commercial agreement between the parties; it should be proportionate and clear.
What to ask the contractor before signing a CCTV maintenance SLA
- A full equipment inventory: cameras, recorders, disks, switches and monitors, with models and locations. If none exists, start with a site survey such as our fire and CCTV technical survey.
- A baseline condition report listing existing faults before the contract starts, so they are not counted against the SLA.
- The critical camera list and the fault classification with examples.
- The time table for each severity, service hours and the call channel.
- How recording availability is measured and reported each month.
- Spare parts scope, the temporary-fix clause, and the deduction or termination mechanism.
These terms also help when you compare quotations: a cheaper offer with no written times can cost more the first time recording stops.
Frequently asked questions
What is an SLA in CCTV maintenance?
It is a schedule in the maintenance contract that sets response time, repair time and recording availability for each fault level, how they are measured, and the consequence of missing them.
Can CCTV maintenance be combined with fire system maintenance in one contract?
Not at AZEIDK. Fire, safety and alarm systems have one contract, and low current and CCTV have a separate one, each with its own SLA.
What is the difference between response time and repair time?
Response time ends when the technician starts work on the call. Repair time ends when the device or recording is back, or when a temporary replacement restores recording.
What response time should a CCTV maintenance contract have?
There is no single value for every facility. It depends on fault level, city, system size and whether a technician is based on site. Each level should have a written time measured from a logged call.
How do I know the cameras are really recording?
Ask for an earlier clip to be retrieved and exported at each visit, review disk error and video loss logs, and make recording availability a line in the monthly report.
Does the contract cover access control and intercom?
The low-current contract can cover them if they appear in the inventory and scope. Anything not in the inventory is outside the SLA.
Conclusion
A CCTV maintenance SLA protects one thing: that the footage exists when you need it. Classify faults, write response and repair times for each level, add a temporary-fix clause and a recording availability target, and ask for a monthly report that proves it. Keep all of this in the low-current and CCTV contract, separate from fire system maintenance. For periodic contracts see preventive and periodic maintenance.
Need an SLA for your CCTV maintenance contract? Send the equipment list, number of sites and required service hours, and our team will draft the scope and time table with you. Talk to the AZEIDK team
Related guides
- Civil Defense Readiness Platform: What It Is, Who Uses It and How It Relates to Salamah
- Furniture Factory Fire Safety: Wood Dust, Spray Shops and Upholstery Stores
- CCTV Shop in Makkah: Directory of Companies and Shops and How to Check Licensing
- Fire Alarm Supplier in KSA: Distributor vs Supplier vs Contractor and How to Verify Authorization







