{"id":25517,"date":"2026-11-15T16:00:20","date_gmt":"2026-11-15T13:00:20","guid":{"rendered":"https:\/\/azeidkgroup.com\/sa\/media-center\/"},"modified":"2026-11-15T16:00:45","modified_gmt":"2026-11-15T13:00:45","slug":"sprinkler-pipe-hangers-supports","status":"publish","type":"post","link":"https:\/\/azeidkgroup.com\/en\/sa\/media-center\/sprinkler-pipe-hangers-supports\/","title":{"rendered":"Sprinkler Pipe Hanger Spacing and Supports Under NFPA 13"},"content":{"rendered":"\t\t<div data-elementor-type=\"wp-post\" data-elementor-id=\"25517\" class=\"elementor elementor-25517 elementor-25516 elementor-bc-flex-widget\" data-elementor-post-type=\"post\">\n\t\t\t\t<div class=\"elementor-element elementor-element-1bda192 e-con-full az-el-article e-flex e-con e-parent\" data-id=\"1bda192\" data-element_type=\"container\" data-e-type=\"container\">\n\t\t\t\t<div class=\"elementor-element elementor-element-c9ba8ae elementor-widget elementor-widget-text-editor\" data-id=\"c9ba8ae\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<p class=\"az-intro\">Sprinkler pipe hanger spacing decides whether a water-filled sprinkler network stays straight and stable for the life of the building. NFPA 13 sets the maximum distance between hangers by pipe material and size, requires at least one hanger on each section of pipe, and limits the unsupported length at the end of a branch line. Consultants check these points before the pressure test and before ceilings are closed.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-3321007 elementor-widget elementor-widget-text-editor\" data-id=\"3321007\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<div class=\"az-keybox\"><h2>Key takeaways<\/h2><ul>\n<li>Hanger spacing comes from an NFPA 13 table by pipe material and size; the edition adopted on your project sets the final values.<\/li>\n<li>NFPA 13 (2019 edition, 17.4.3.2.1) requires not less than one hanger for each section of pipe, apart from specific exceptions.<\/li>\n<li>Hangers attach to the structure (concrete or steel), never to a suspended ceiling, ductwork or other services.<\/li>\n<li>The end sprinkler on a branch line and armovers have unsupported-length limits, with tighter limits at higher pressure or where seismic protection is designed.<\/li>\n<li>Hanger defects are among the most common acceptance comments, and fixing them after ceilings go in is expensive.<\/li>\n<\/ul><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-6cbda9c elementor-widget elementor-widget-text-editor\" data-id=\"6cbda9c\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>Why do consultants inspect sprinkler hangers so closely?<\/h2>\n<p>A sprinkler network does not only carry the weight of empty pipe. It is full of water at all times, it sees surges when the fire pump starts, and it takes extra load when a sprinkler opens or during the hydrostatic test. A weak or badly spaced hanger lets the pipe sag, changes the network slope, traps water and keeps the joints under constant stress.<\/p>\n<p>That is why hanger items appear on shop drawings and on consultant inspection checklists as part of <a href=\"\/en\/sa\/media-center\/fire-fighting-system-installation-saudi\/\">fire fighting system installation<\/a>. The AZEIDK <a href=\"\/en\/sa\/services\/installation-implementation\/\">installation team<\/a> sets hangers before running branch lines, because the hanger fixes the pipe route and level.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-3692b75 elementor-widget elementor-widget-text-editor\" data-id=\"3692b75\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>What is the sprinkler pipe hanger spacing in NFPA 13?<\/h2>\n<p>NFPA 13 gives a table of maximum distance between hangers (Table 17.4.2.1(a) in the 2019 edition). The steel pipe values below are the ones commonly quoted in published NFPA 13 study summaries for sprinkler designers and technicians. Check them against the edition adopted on your project before using them on drawings.<\/p>\n<div class=\"az-table-wrap\"><table>\n<thead><tr><th>Item<\/th><th>Commonly quoted value<\/th><th>Note<\/th><\/tr><\/thead>\n<tbody>\n<tr><td>Steel pipe, 1 in. and 1-1\/4 in.<\/td><td>12 ft (about 3.7 m) between hangers<\/td><td>Typically branch lines<\/td><\/tr>\n<tr><td>Steel pipe, 1-1\/2 in. and larger<\/td><td>15 ft (about 4.6 m)<\/td><td>Larger branch lines and mains<\/td><\/tr>\n<tr><td>Last hanger to end sprinkler on a branch line<\/td><td>36 in. for 1 in. pipe, 48 in. for 1-1\/4 in., 60 in. for 1-1\/2 in. and larger<\/td><td>Unsupported length at the end of the line<\/td><\/tr>\n<tr><td>Armover to a sprinkler<\/td><td>24 in. for steel pipe, with a shorter limit at high pressure to be checked in the standard<\/td><td>Longer armovers need their own hanger<\/td><\/tr>\n<tr><td>Hanger to an upright sprinkler<\/td><td>At least 3 in.<\/td><td>Keeps the hanger clear of the sprinkler<\/td><\/tr>\n<\/tbody><\/table><\/div>\n<p>CPVC and copper have shorter spans than steel and also depend on the manufacturer&#8217;s listing. If the network uses <a href=\"\/en\/brand\/kdi\/\">KDI<\/a> pipe or any other brand, read the datasheet with the table; wall thickness (SCH 10 or SCH 40) does not change the one-hanger-per-section rule.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-da235ca elementor-widget elementor-widget-text-editor\" data-id=\"da235ca\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>One hanger per section of pipe: how does it work on site?<\/h2>\n<p>Section 17.4.3.2.1 of the 2019 edition requires not less than one hanger for each section of pipe, with exceptions in the sections that follow it. In practice, a short piece between two closely spaced sprinklers or between two elbows is not left hanging on the grooved couplings at its ends.<\/p>\n<p>One known exception covers a continuous pipe with welded or mechanical outlets, where spacing follows the table directly. Exceptions are not applied by judgment on site; they are shown on the shop drawings and accepted by the consultant.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-3fc0aa6 elementor-widget elementor-widget-text-editor\" data-id=\"3fc0aa6\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>Types of sprinkler pipe hangers used on Saudi sites<\/h2>\n<p>A hanger assembly has three parts: the part that holds the pipe, a rod or bracket that carries the load, and the attachment to the building. NFPA 13 generally requires hanger components to be listed for sprinkler service, with cases where the standard accepts hangers designed and certified by a responsible engineer; check the adopted edition for the conditions.<\/p>\n<div class=\"az-table-wrap\"><table>\n<thead><tr><th>Type<\/th><th>Typical use<\/th><th>What to check on site<\/th><\/tr><\/thead>\n<tbody>\n<tr><td>Adjustable clevis or band hanger<\/td><td>Branch lines and mains under the slab<\/td><td>Ring size matches the pipe; nut tightened<\/td><\/tr>\n<tr><td>Threaded rod<\/td><td>Carries load from the ring to the attachment<\/td><td>Diameter per the standard&#8217;s table for the pipe size; no bending<\/td><\/tr>\n<tr><td>Beam clamp<\/td><td>Steel beams and joists<\/td><td>Orientation per manufacturer; retaining strap where required<\/td><\/tr>\n<tr><td>Concrete anchor or cast-in insert<\/td><td>Concrete slabs and beams<\/td><td>Anchor type and depth per manufacturer; not near slab edges<\/td><\/tr>\n<tr><td>Wall bracket<\/td><td>Vertical runs and pipes along walls<\/td><td>Fixed to a structural wall, not a gypsum partition<\/td><\/tr>\n<tr><td>Trapeze<\/td><td>Where no structural member sits directly above the pipe<\/td><td>Cross member sized for the span and load<\/td><\/tr>\n<\/tbody><\/table><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-3983992 elementor-widget elementor-widget-text-editor\" data-id=\"3983992\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>Attachment to concrete and steel: where mistakes happen<\/h2>\n<h3>Concrete slabs<\/h3>\n<p>Use listed mechanical anchors or cast-in inserts placed before the pour. Common mistakes are an anchor that does not suit the load, anchors in hollow-core slabs without the manufacturer&#8217;s guidance, or anchors too close to the slab edge. In existing buildings, locate the reinforcement before drilling so bars are not cut.<\/p>\n<h3>Steel structures<\/h3>\n<p>Beam clamps are quick, but they must sit the right way on the flange. In warehouses and metal-roof buildings, never hang from roof sheeting or from light purlins that were not designed for the load.<\/p>\n<h3>What a hanger must not hang from<\/h3>\n<p>Fire pipes do not hang from suspended ceilings, HVAC ducts or other service pipes. This comment shows up often on fit-out jobs when the fire team arrives after the other trades.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-c473d09 elementor-widget elementor-widget-text-editor\" data-id=\"c473d09\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>Seismic sway bracing: when does it apply?<\/h2>\n<p>Hangers carry weight vertically. Sway braces stop the network moving sideways and lengthwise, and they apply when the designer protects the system against earthquakes based on the project location and requirements. In that case NFPA 13 (2025 edition) calls for lateral braces at not more than 40 ft on mains, longitudinal braces at not more than 80 ft, and a four-way brace at the top of every riser, with calculations attached to the drawings. Do not assume your project needs it or not; the decision belongs in <a href=\"\/en\/sa\/services\/shop-drawings-coordination\/\">shop drawings and coordination<\/a> with the consultant.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-2f6a446 elementor-widget elementor-widget-text-editor\" data-id=\"2f6a446\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>Hanger defects that come up at acceptance<\/h2>\n<ul>\n<li>A short pipe section with no hanger, carried only by two grooved couplings.<\/li>\n<li>The end sprinkler on a branch line too far from the last hanger.<\/li>\n<li>A long armover to a sprinkler with no hanger of its own.<\/li>\n<li>A hanger right next to a sprinkler, interfering with the spray pattern.<\/li>\n<li>A bent rod, or an over-long rod with no lateral restraint.<\/li>\n<li>A hanger fixed to the suspended ceiling or an HVAC duct.<\/li>\n<li>Loose nuts, or a ring larger than the pipe.<\/li>\n<li>A change of direction on a main with no nearby hanger as shown on the approved drawings.<\/li>\n<\/ul>\n<p>These are far easier to spot before the ceiling goes in. We tie the hanger check to the pressure test: the network is inspected visually, then goes through the <a href=\"\/en\/sa\/media-center\/fire-fighting-hydrostatic-pressure-test\/\">hydrostatic pressure test<\/a> fully supported, and the hangers are watched during the test.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-c30e9eb elementor-widget elementor-widget-text-editor\" data-id=\"c30e9eb\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>Practical steps before hanging the pipe<\/h2>\n<ol>\n<li>Approve shop drawings that show hanger locations and types, not only the pipe route.<\/li>\n<li>Approve the submittal datasheets for hangers, anchors and beam clamps.<\/li>\n<li>Identify the structure above each run: slab, concrete beam or steel beam.<\/li>\n<li>Coordinate levels with HVAC and electrical before drilling.<\/li>\n<li>Fix hangers before lifting the pipe, then set slope and level.<\/li>\n<li>Self-inspect, then call the consultant before the pressure test.<\/li>\n<\/ol>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-e84681a elementor-widget elementor-widget-text-editor\" data-id=\"e84681a\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>Frequently asked questions<\/h2>\n<div class=\"az-faq\">\n<details class=\"az-faq__item\"><summary><h3>What is the sprinkler pipe hanger spacing for steel pipe?<\/h3><\/summary><p>The commonly quoted values are 12 ft for 1 in. and 1-1\/4 in. steel and 15 ft for 1-1\/2 in. and larger, with one hanger per pipe section. Final values come from the adopted NFPA 13 edition.<\/p><\/details>\n<details class=\"az-faq__item\"><summary><h3>Is one hanger every 15 ft enough if the pipe sections are short?<\/h3><\/summary><p>Usually not. The general rule is one hanger per section of pipe; exceptions are specific and need the consultant&#8217;s acceptance.<\/p><\/details>\n<details class=\"az-faq__item\"><summary><h3>Can a sprinkler pipe hang from an HVAC duct?<\/h3><\/summary><p>No. Hangers attach to the building structure, not to equipment or other services.<\/p><\/details>\n<details class=\"az-faq__item\"><summary><h3>What is the difference between a hanger and a sway brace?<\/h3><\/summary><p>A hanger carries vertical load. A sway brace resists lateral and longitudinal movement and is needed when the design includes seismic protection.<\/p><\/details>\n<details class=\"az-faq__item\"><summary><h3>Does CPVC pipe have different hanger spacing?<\/h3><\/summary><p>Yes. Spans are shorter than steel and depend on ambient temperature; they come from the standard and the manufacturer&#8217;s listing.<\/p><\/details>\n<details class=\"az-faq__item\"><summary><h3>When are hangers inspected?<\/h3><\/summary><p>Before ceilings close and before or during the pressure test, then again at final acceptance as part of the handover file.<\/p><\/details>\n<\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-b916e2e elementor-widget elementor-widget-text-editor\" data-id=\"b916e2e\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<h2>Conclusion<\/h2>\n<p>Hangers are a small detail on the drawing and a big one on site. Show hanger locations on the shop drawings, keep one hanger per section, check end sprinklers and armovers, and attach only to structure. More on the full network on our <a href=\"\/en\/sa\/solutions\/fire-fighting-systems\/\">fire fighting systems<\/a> page.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-cf9defc elementor-widget elementor-widget-text-editor\" data-id=\"cf9defc\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<p class=\"az-cta\"><strong>Have a sprinkler network under construction or open hanger comments?<\/strong> Send the drawings and site photos and the AZEIDK installation team will review them. <a href=\"\/en\/sa\/contact\/\">Talk to the AZEIDK team<\/a><\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<div class=\"elementor-element elementor-element-f95dcbd elementor-widget elementor-widget-text-editor\" data-id=\"f95dcbd\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<div class=\"az-source\"><strong>References:<\/strong> NFPA 13, 2019 edition, Section 17.4.3.2.1 and Table 17.4.2.1(a), as quoted in a MeyerFire discussion; NFPA 13 hanger spacing summary, OpenExamPrep NICET water-based systems study guide, Section 10.2; LADBS Plan Check Correction Sheet for NFPA 13, 2025 edition, City of Los Angeles (sway brace items 111 to 119); AZEIDK KDI fire protection pipe product page; sprinkler checklist, Oklahoma City Fire Marshal&#8217;s Office.<\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t","protected":false},"excerpt":{"rendered":"<p>Sprinkler pipe hanger spacing under NFPA 13: distances by pipe size, one hanger per section, fixing to concrete and steel, and common acceptance defects.<\/p>\n","protected":false},"author":0,"featured_media":25322,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[221,321,320],"tags":[],"azeidk_region":[223],"class_list":["post-25517","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-azeidk-articles","category-codes-certifications-en","category-codes-certifications-ar"],"acf":[],"_links":{"self":[{"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/posts\/25517","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/types\/post"}],"replies":[{"embeddable":true,"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/comments?post=25517"}],"version-history":[{"count":1,"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/posts\/25517\/revisions"}],"predecessor-version":[{"id":25949,"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/posts\/25517\/revisions\/25949"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/media\/25322"}],"wp:attachment":[{"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/media?parent=25517"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/categories?post=25517"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/tags?post=25517"},{"taxonomy":"azeidk_region","embeddable":true,"href":"https:\/\/azeidkgroup.com\/en\/wp-json\/wp\/v2\/azeidk_region?post=25517"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}